Beelink EQ12 Pro - Wake On LAN

neurone

Hello, I'm trying to configure Wake On LAN for my Beelink EQ12 Pro but the only options that works in the BIOS are wake on fixed time or in 1-5 minutes after the boot.




I verified via tcpdump the magic packets arrive when the machine is on, but when it's off it never wakes up.
I tried all the configuration there (Disabled, Fixed Time, Dynamic), but maybe that setting is just for RTC.

I Wake-On-LAN via magic packet supported? If it is, how can I enable it?

Thanks!

tuiguang16

Hello, I have uploaded the tutorial into the attachment, please have a check.

kabello

I have the same issue, but I'm not using Windows, I'm using Linux, how can I solve this issue?

Thx!

neurone

Thanks for the answer but I'm using Linux also. The WoL is already enabled in Linux (see details below, Wake-on is set to "g" that means use the Magic Packet), but it does not work. Is there a specific configuration in the BIOS for the WoL to work/not work?

1. $ sudo ethtool enp1s0
   
2. Settings for enp1s0:
   
3.         Supported ports: [ TP ]
   
4.         Supported link modes:   10baseT/Half 10baseT/Full
   
5.                                 100baseT/Half 100baseT/Full
   
6.                                 1000baseT/Full
   
7.                                 2500baseT/Full
   
8.         Supported pause frame use: Symmetric
   
9.         Supports auto-negotiation: Yes
   
10.         Supported FEC modes: Not reported
    
11.         Advertised link modes:  10baseT/Half 10baseT/Full
    
12.                                 100baseT/Half 100baseT/Full
    
13.                                 1000baseT/Full
    
14.                                 2500baseT/Full
    
15.         Advertised pause frame use: Symmetric
    
16.         Advertised auto-negotiation: Yes
    
17.         Advertised FEC modes: Not reported
    
18.         Speed: 2500Mb/s
    
19.         Duplex: Full
    
20.         Auto-negotiation: on
    
21.         Port: Twisted Pair
    
22.         PHYAD: 0
    
23.         Transceiver: internal
    
24.         MDI-X: off (auto)
    
25.         Supports Wake-on: pumbg
    
26.         Wake-on: g
    
27.         Current message level: 0x00000007 (7)
    
28.                                drv probe link
    
29.         Link detected: yes
    
30. $ sudo ethtool enp2s0
    
31. Settings for enp2s0:
    
32.         Supported ports: [ TP ]
    
33.         Supported link modes:   10baseT/Half 10baseT/Full
    
34.                                 100baseT/Half 100baseT/Full
    
35.                                 1000baseT/Full
    
36.                                 2500baseT/Full
    
37.         Supported pause frame use: Symmetric
    
38.         Supports auto-negotiation: Yes
    
39.         Supported FEC modes: Not reported
    
40.         Advertised link modes:  10baseT/Half 10baseT/Full
    
41.                                 100baseT/Half 100baseT/Full
    
42.                                 1000baseT/Full
    
43.                                 2500baseT/Full
    
44.         Advertised pause frame use: Symmetric
    
45.         Advertised auto-negotiation: Yes
    
46.         Advertised FEC modes: Not reported
    
47.         Speed: 1000Mb/s
    
48.         Duplex: Full
    
49.         Auto-negotiation: on
    
50.         Port: Twisted Pair
    
51.         PHYAD: 0
    
52.         Transceiver: internal
    
53.         MDI-X: off (auto)
    
54.         Supports Wake-on: pumbg
    
55.         Wake-on: g
    
56.         Current message level: 0x00000007 (7)
    
57.                                drv probe link
    
58.         Link detected: yes
    

复制代码

tuiguang16

Hello there,

Here is the tutorial for your linux system, you can have a try-----https://technotim.live/posts/wake-on-lan/
Looking forward to your feedback so that we can help you better.

neurone

Hello, I answered with another message that my problem is solved. That message is still in "moderation", I'm not sure why and I'm not sure if this will be seen before that message. In any case, thanks. If you can publish my previous message, I explain how I solved; that can useful for other people too.

tuiguang16

Hello, now I just can see the message that you said your issue has been solved, and your message is not posted.
So maybe you can have a post again, and please be careful not to include any sensitive keywords.

If your message is still can not be posted, you can contact our support email----support-pc@bee-link.com
We will share your method to other customer, thanks.

Typys

neurone replied at 2023-11-07 02:56
Hello, I answered with another message that my problem is solved. That message is still in "moderati ...

Hello, any chance you can share how you solved? I have the same problem and it’s driving me nuts