Please select To the mobile version | Continue to access the desktop computer version
123Next
Return to list New
View: 3659|Reply: 22

GTR6 no HDMI output at all

[Copy link]

1

Threads

2

Posts

43

Credits

Newbie

Rank: 1

Credits
43
Post time 2023-02-05 22:58:47 | Show all posts |Read mode
my brand new GTR6 has no HDMI output at all

i used all shipped cables to set it up.
after powering on, the screen stays black with no hdmi signal, even no post or BIOS is reachable.
Reply

Use magic Report

1

Threads

8

Posts

63

Credits

Member

Rank: 2

Credits
63
Post time 2023-02-06 18:28:36 | Show all posts
My monitor didn't work either - until I found an "enable legacy HDMI" setting on it - then it did!  Something to look for if you have the option! :)
Reply Support 1 Not support 0

Use magic Report

0

Threads

1

Posts

18

Credits

Newbie

Rank: 1

Credits
18
Post time 2023-02-06 06:58:18 | Show all posts
I have this exact same problem. My friend ordered me a barebones GTR6 and some RAM and SSD, I tried using it without them plugged in and with them, all four of the hdmi ports do not work either with my TV or my Dell Monitor. I've used multiple HDMI cables as well. I have about eight different HDMI cables, ranging from 8k to 4k. I also tried unplugging the CMOS battery for a while and then plugging it back in, as well as trying to reset the CMOS through the button on the front with the PDF tutorial. I have no signal from HDMI device on both the monitor and the TV.
Reply Support Not support

Use magic Report

2

Threads

152

Posts

468

Credits

Full Member

Rank: 3Rank: 3

Credits
468
Post time 2023-02-06 09:21:52 | Show all posts
It's been 2 days now - has anyone reached out to you?
Reply Support Not support

Use magic Report

3

Threads

1762

Posts

5402

Credits

Super Moderator

Rank: 8Rank: 8

Credits
5402
Post time 2023-02-06 17:40:52 | Show all posts
Hello,
Pls contact our email.
Could you pls send  a picture of SN at the bottom of the machine and your purchase record?
Just balck screen?
Does the fan rotate?
Does the instruction led light up?

1.Please change another HDMI cable or power supply.

2.Please unplug the power supply and HDMI cable. Please try to hit the hole of "CLR CMOS" with a needle or a pin for about 5-10 seconds.Ten minutes later, plug the power supply and HDMI cable, turn on the PC again.

3.There might be something wrong with the hard ware components.Please take out the SSD and RAM and then put them back , make sure they are installed properly.

Also please clean the gold finger with a rubber.Here is the tutorial  https://www.youtube.com/watch?v=hEd_7nmWVOk  

If it still doesn’t work, please press delete key as soon as you turn on the PC, so that you can go to BIOS, please check you can see SSD there.
Reply Support Not support

Use magic Report

1

Threads

2

Posts

43

Credits

Newbie

Rank: 1

Credits
43
 Author| Post time 2023-02-07 16:09:17 | Show all posts
Support-03 replied at 2023-02-06 17:40
Hello,
Pls contact our email.
Could you pls send  a picture of SN at the bottom of the machine and y ...

Hello I tried all as described, no improvement.
I never was able to get into BIOS or see a Beelink logo at start up.

The Power LED is on, the fans spin, after a while the large fan increase. the speed.

To which email I need to send the serial and purchase details?


Regards
Reply Support Not support

Use magic Report

0

Threads

49

Posts

264

Credits

Full Member

Rank: 3Rank: 3

Credits
264
Post time 2023-02-07 23:43:42 | Show all posts
Annoyed replied at 2023-02-07 16:09
Hello I tried all as described, no improvement.
I never was able to get into BIOS or see a Beelink ...

This is their support email address.
support-pc@bee-link.com
Reply Support Not support

Use magic Report

1

Threads

5

Posts

77

Credits

Member

Rank: 2

Credits
77
Post time 2023-02-28 07:04:21 | Show all posts
I have same problem.  I even can't see BIOS.
Reply Support Not support

Use magic Report

0

Threads

1

Posts

16

Credits

Newbie

Rank: 1

Credits
16
Post time 2023-03-31 07:38:18 | Show all posts
Is there any update on this? I'm exactly in the same situation.
The fan works and looking at the power consumption (I have a power meter) and on the fan sound, it's like there is a Windows logon. But no image at all.

Is there any way to force a BIOS flash for a newer version (I heard of a new HDMI driver) just by using a USB flash drive or so? Or to do it like a blind, with precise steps...
Reply Support Not support

Use magic Report

3

Threads

1762

Posts

5402

Credits

Super Moderator

Rank: 8Rank: 8

Credits
5402
Post time 2023-04-04 18:17:26 | Show all posts
fearbrain replied at 2023-03-31 07:38
Is there any update on this? I'm exactly in the same situation.
The fan works and looking at the pow ...

Hello,
Pls contact our email.
Reply Support Not support

Use magic Report

You have to log in before you can reply Login | Sign up

Points Rules

Quick Reply To Top Return to the list