Please select To the mobile version | Continue to access the desktop computer version
View: 957|Reply: 5

Gtr5 sharing ethernet.

[Copy link]

1

Threads

13

Posts

111

Credits

Member

Rank: 2

Credits
111
Post time 2022-07-13 23:43:00 | Show all posts |Read mode
Edited by rmilance at 2022-07-13 23:44

Its possible sharing dual port ethernet in power off pc, adapter alimentation power on ? Led not blinking...
Reply

Use magic Report

3

Threads

1767

Posts

5418

Credits

Super Moderator

Rank: 8Rank: 8

Credits
5418
Post time 2022-07-14 17:53:35 | Show all posts
Hello there,

Do you have two PC ?
If one PC is turned off, you cannot share the dual por ethernet.
Any questions, please let us know.

Best regards,
George
Reply Support Not support

Use magic Report

1

Threads

13

Posts

111

Credits

Member

Rank: 2

Credits
111
 Author| Post time 2022-07-14 22:26:21 From the mobile phone | Show all posts
Hello, On old pc's I always saw that there was a signal led that blinked with the power on, but I never had a dual ethernet port to try, so I thought it might work as a router. I would like to connect the GtKingPro with the GTR5 turned off. Thanks
Reply Support Not support

Use magic Report

1

Threads

13

Posts

111

Credits

Member

Rank: 2

Credits
111
 Author| Post time 2022-07-14 22:53:10 From the mobile phone | Show all posts
After all, it is logical that the ports are active if the power supply is turned on, how would wake on lan work?
Reply Support Not support

Use magic Report

1

Threads

13

Posts

111

Credits

Member

Rank: 2

Credits
111
 Author| Post time 2022-07-24 12:58:53 From the mobile phone | Show all posts
Advanced Configuration Power management Interface (ACPI)—power management for modern operating systems that are capable of Operating System-directed Power Management (OSPM)—is supported to achieve the most efficient power management possible. PCI MSI (Message Signaled Interrupt) and MSI-X are also supported.  In addition to the ACPI feature, remote wake-up (including AMD Magic Packet and Microsoft Wake-Up Frame) is supported in both ACPI and APM (Advanced Power Management) environments. To support WOL from a deep power down state (e.g., D3cold, i.e., main power is off and only auxiliary exists), the auxiliary power source must be able to provide the needed power for the RTL8125BG/RTL8125BGS. To further reduce power consumption, the RTL8125BG/RTL8125BGS also supports PCIe L1 substate L1.1 and L1.2.  The RTL8125BG/RTL8125BGS supports ‘RealWoW!’ technology that enables remote wake-up of a sleeping PC through the Internet. This feature allows PCs to reduce power consumption by remaining in low power sleeping state until needed.  Note: The ‘RealWoW!’ service requires registration on first time use.  The RTL8125BG/RTL8125BGS supports Protocol offload. It offloads some of the most common protocols to NIC hardware in order to prevent spurious Wake-Up and further reduce power consumption. The RTL8125BG/RTL8125BGS can offload ARP (IPv4) and NS (IPv6) protocols while in the D3 power saving state.
Reply Support Not support

Use magic Report

0

Threads

22

Posts

412

Credits

Full Member

Rank: 3Rank: 3

Credits
412
Post time 2022-07-26 15:07:26 | Show all posts
To have ports do anything more than just receive wake up call (magic packets) you need them to be:
- be a part of a switch (those are not being separate two network cards)
- have another chipset behind them that act as a router (there is none)
- have the whole infrastructure to keep those things set up and configurable (there is none)
So what you would like to do requires just a running operating system that can do a network switch (called a bridge in this case in Windows) or router - so a system running at full speed.

Why Wake-on-Lan is easy but not the other stuff?
WoL to run need just to look for simple pattern and if it matches - to send an interrupt to the rest of the system to wake it up.
Reply Support Not support

Use magic Report

You have to log in before you can reply Login | Sign up

Points Rules

Quick Reply To Top Return to the list