GT1 Ultimate b706db flashing 7% error

jkbadouvas

Hi everyone,

Few days ago, I decided to upgrde my Beelink GT1 Ultimate (S/N B706DB). For some unidentified reason, the ROM did not install and my gt1 ultimate b706db got bricked.

Every time I try to flash it with the USB tool, I get to 7% (best case scenario) . With SD, I am stuck at "upgrading" screen. stays there for ages. I even left it overnight.

I have tried all sort of ROMs I could find for my model but no luck. Also two cables , 4 computers and all their ports. Two oses (win 10,7) all possible combinations for erasing flash and bootloader.

I think my device is in boot loop as it always try to boot from SD card. When I connect the box to my pc, USB Burning tool detects it automatically without needing to press reset button with a toothpick. Is this normal?

Probably the bootloader is damaged?

Any possible idea what I can do?

It is driving me crazy! I do not want to throw away my Beelink.

beelink

Please select the correct firmware for burning. If the computer can read your machine correctly, it can be burned again. Check the firmware and burning guide in the link for burning. After the burning starts, please plug in the power to avoid insufficient power Causes the burning to fail.
http://www.bee-link.com/forum.ph ... amp;extra=#pid54663

jkbadouvas

Hi beelink,

I have done all the steps you suggested but my box refuses to move after 7%.

I think that my emmc has become read-only and does not accept any changes.

what else can I do? the SD card method simply doesnt work.

thank you,
John

beelink

jkbadouvas replied at 2020-04-21 19:29
Hi beelink,

I have done all the steps you suggested but my box refuses to move after 7%.

Hello，
If you still fail to try to burn multiple times, you can send the wrong photo taken to 7% of the times to our after-sales mailbox, and our after-sales technical support staff will determine why the error occurred.

jkbadouvas

Ok. I will do,

can you please tell me the email?

thank you

jkbadouvas

I have never, never ever in my life have experienced such a disgraceful aftersales service.

You asked me for a photo of my problem to your aftersales email. I requested the email address 4 days ago and you still did not take 5 minutes to write me that address. You had to write a simple email address and you just never did!

In fact, I found the address on my own, I sent an email - again 4 days ago- and no one bothered enough to reply to me.

I have a product that got bricked when performing YOUR update and have no clue why, no help to unbrick and last but not least, is a model with FAKE ram! it has 2GB instead of 3GB! I was cheated in first place and now not even receiving an answer.

The worst company I could ever chose.

Be sure, it will never happen again. There are many other brands such as TANIX and Mecool that we can trust.

beelink

jkbadouvas replied at 2020-04-26 07:39
I have never, never ever in my life have experienced such a disgraceful aftersales service.

You ask ...

Hello，
Sorry for the inconvenience, because there is a post-sale email address at the bottom of our website, so no address is attached. Our post-sale email address is beelinkservice@bee-link.com, you may have sent the wrong address because We did not receive your email after careful inquiry. About RAM has 3G but the only 2G is read. This is a firmware problem. We fixed this problem a long time ago.

jkbadouvas

I have sent you again the same email.

the previous one was sent by me business email address jk.badouvas@cretan***.gr
you can certainly find it if you look better.

I am still expecting a prompt answer.

Not in one week.

thank you

beelink

jkbadouvas replied at 2020-04-26 21:23
I have sent you again the same email.

the previous one was sent by me business email address jk.bad ...

Hello，Sorry, your email was intercepted in our spam mailbox, I found it based on the email you provided, we have replied to you, please check it.

kobeml

What was the reply from Beelink service? I have been having the same issue - flashing stops at 7% with 2 images suggested here by beelink and SD card method is not feasible since I have No Signal on TV from the box.