Help required for Beelink GT1 Ultimate

Kashif

Dear All

Please help me.... as I had upgraded my gt1 ultimate from setting. After upgrading successfully device started hanging and was unable to reset completely.

After contacting with Beelink, I received the firmware, burning toll and a video tutorial to reset from bottom hole with the pin and proceed as per the instructions.

I had tried alot but unable to reset from bottom hole, as I am holding for long time correctly,,,,,,,,,,,,, nothing happend

now I have following issues,,,,,,,,,,,,,,, please guide me to resolve it.

1. my remore is not wirking with gt1 ultimate, however it is working with my tv
2. when i m plugging the device white light is turning on and there is no dispaly, as my tv is 100% OK and working with all my other devices
3. sometime device shows beelink red color logo and freezes................... and no other display or......................
4. unable to reset with bottom hole.

I'll really greatful if you will guide me as my gt1 ultimate is useless for me

beelink

:dizzy:

Kashif

Admn.... I need a support from Beelink but it seems there is no one interested to provide me the same??????????????????

Phant0m``

I typically avoid answering these types of posts. I try aiding, and I get moderated every-time. Beelink Message board software is frustrating.

Phant0m``

You going to have to revive your box by downloading the EPROM for the firmware version that you was running before attempting to upgrade. What is the first four digits of your serial number...? can be found by looking at the bottom of your Beelink box.

You'll need to download Amlogic Burn Card Maker v2.0.2 utility and make bootable SD Card using this EPROM file. It doesn't matter if you can't get into recovery mode, or if there's no signal to TV.

Insert the Micro-SD card in, and unplug the power adapter from the box. Insert the paper-clip end into the RESET hole and carefully press down and hold the button in. Carefully hook up the power adapter while maintaining the RESET button down for the duration of five - seven seconds. After which time you can release the RESET button, and leave the box sit for however long it takes for it to reprogram and re-boot itself. You'll finally see signal from Beelink to TV and be entering the Beelink setup phase. :P

Kashif

thanks and appreciated your prompt reply.

Please note the last 4 digits of my box serial number (0064). Its gt1 Ultimate

Please send me the link of EPROM flashing to download and follow your instructions as above

Kashif

and its G912

Phant0m``

Kashif replied at 2017-09-06 10:36
and its G912

It's only the first four digits that matters.. :)


Beelink GT1 Standard / Ultimate Editions S912/G912 (2GB+16 / 2GB+32GB / 3GB+32GB) QCA9377(WiFi+BT) 1000Mbps Ethernet

GT1_703N0_LTM8830-Test (QCA9377) | July 17th, 2017
   Based On: GT1_702N0
   Android Version: 7.1.2
   Serial Number Compatibility (S/N): S912..., G912...
   OTA (Over-The-Air) Released: No
   SD Card Upgrading: Yes... Android 7.x to 7.xyz
   EPROM Firmware: Yes
   Official Link: http://www.bee-link.com/Beelink-13895-1-1.html

Kashif

as per your above instructions I ve downloaded Amlogic Burn Card Maker v2.0.2 utility to make bootable SD Card using this EPROM file.

1. it is chinese language
2. in your above link there are 3 files (1. factory_update_param.aml... 2. recovery.img and 3. q201-ota-20170712.zip)

Please guide me how i ll make sd card bootable in chinese software and which file from above three download should attach in card maker

Phant0m``

Can't post more details... Being moderated ... like always.