12Next
Return to list New
View: 5341|Reply: 10

Brick after supersu

[Copy link]

3

Threads

12

Posts

134

Credits

Member

Rank: 2

Credits
134
Post time 2017-08-01 13:29:00 | Show all posts |Read mode
Guys i have big problem after install supersu and restart, nothing works burning tool only 4%, burn card maker all img firm, sd card method minus. nothing work hdmi no detect how solved this......?
Reply

Use magic Report

17

Threads

725

Posts

6171

Credits

Moderator

Rank: 7Rank: 7Rank: 7

Credits
6171
Post time 2017-08-27 21:33:40 | Show all posts
kumara29 replied at 2017-08-27 08:52
what cable did you plug ? power cable to  GT1 ?

Yes... Person was talking about the Power cord
Beelink GT1 Mini (95X2) w/CoreELEC & Android 9 (Pie)
Reply Support 1 Not support 0

Use magic Report

391

Threads

4189

Posts

110K

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
12739
Post time 2017-08-01 19:23:10 | Show all posts
hello dear , tell me more information about your GT1 and I will choose the right firmware for you to have a try again , thank you .:hug:
Reply Support Not support

Use magic Report

3

Threads

12

Posts

134

Credits

Member

Rank: 2

Credits
134
 Author| Post time 2017-08-01 22:12:04 | Show all posts
Edited by ECGT80 at 2017-08-01 22:20

Hello, at first I had the GT1-703NO version installed for the AP6255 (GT1 Ultimate), it seems that from the play store I installed Supersu, I install the binaries, and then it asks me to restart and I make a normal restart from supersu from here. Problems was left in the image of loading and did not finish turning on then between the recovery and I did not work the remote control of vol up neither the bottom nor the arrows, nothing simply turned off with any button that pressed and then restarted then I wanted to use the burning tool and it only reaches me 4% (I never run this tool I do not know why) then I wanted to use the "Burn Card Maker" use a 2GB Sdcard memory in FAT and turned on and started with the "Upgrade" Was about 5 minutes not even appeared the installation bar and turned off the HDMI connection after that wait a long time and nothing (30 minutes) so I decided to turn it off and on again and now Not even HDMI connection does not recognize it use several img with "burn card maker" and everything was in vain I can not relive the pc if it recognizes but only reaches 4% as always. any solution????

Sorry for my english

Español:
Hola, en un principio tenia instalado la version GT1-703NO para el modelo AP6255  (GT1 Ultimate) resulta que desde play store instale Supersu, instalo los binarios concluyo y luego me pide reiniciar y realizo un reinicio normal desde supersu a partir de ahy surgieron mis problemas se quedaba en la imagen de cargando y no terminaba de encender entonces entre al recovery y no me funcionaba el control remoto de vol arriba ni el de abajo ni las flechas, nada simplemente se apagaba con cualquier boton que presionaba y se volvia a reiniciar entonces quise utilizar el burning tool y solo me llega al 4% (Nunca me funciono esta herramienta no se porque) luego quise utilizar el "Burn Card Maker" utilice una memoria de 2GB Sdcard en FAT y encendio y empezo con el mensaje de "Upgrade" estuvo asi unos 5 minutos ni siquiera aparecio la barra de instalacion y se apago se corto la conexion HDMI luego de eso espere bastante tiempo y nada (30 minutos) entonces decidi apagarlo y volverlo a encender y ya ni siquiera existe conexion HDMI no lo reconoce utilice varios img con "burn card Maker" y todo fue en vano no logro revivirlo la pc si lo reconoce pero solo llega al 4% como siempre. alguna solucion????
Reply Support Not support

Use magic Report

3

Threads

12

Posts

134

Credits

Member

Rank: 2

Credits
134
 Author| Post time 2017-08-03 07:23:10 | Show all posts
This solved, I needed energy so I put the plug of the cable to the device (and not just with the USB cable) to be able to install the software through USB Burning Tool, Thanks ...
Reply Support Not support

Use magic Report

1

Threads

19

Posts

97

Credits

Member

Rank: 2

Credits
97
Post time 2017-08-27 20:52:22 | Show all posts
ECGT80 replied at 2017-08-03 07:23
This solved, I needed energy so I put the plug of the cable to the device (and not just with the USB ...

what cable did you plug ? power cable to  GT1 ?
Reply Support Not support

Use magic Report

1

Threads

19

Posts

97

Credits

Member

Rank: 2

Credits
97
Post time 2017-08-28 01:15:01 | Show all posts
USB firmware upgrading don't need power cable as per tutorial video by beelink
Reply Support Not support

Use magic Report

1

Threads

19

Posts

97

Credits

Member

Rank: 2

Credits
97
Post time 2017-08-28 15:06:55 | Show all posts
Phant0m`` replied at 2017-08-27 21:33
Yes... Person was talking about the Power cord

Thanks alot Phant0m & ECGT80

Plugging power cable to GT1 Ultimate. i was able to upgrade firmware.
Reply Support Not support

Use magic Report

3

Threads

12

Posts

134

Credits

Member

Rank: 2

Credits
134
 Author| Post time 2017-08-29 21:51:50 | Show all posts
Note: For me only work when no work hdmi output when turn on box.

Nota: para mi solo solo me funciono este metodo cuando no conecta el hdmi al encender el tv box
Reply Support Not support

Use magic Report

0

Threads

1

Posts

22

Credits

Newbie

Rank: 1

Credits
22
Post time 2017-08-30 03:03:11 | Show all posts
Hi guys!I have the same problem,only burning to stop at 7%,the TV does not see the console via hdmi.I tried different solution to the problem mentioned on the forum,but neither of which did not help.beelink gt,1(A912).2g/32g.
Reply Support Not support

Use magic Report

12Next
Return to list New
You have to log in before you can reply Login | Sign up

Points Rules

Quick Reply To Top Return to the list