How to make factory reset on Beelink SER7 Mini PC W11 Pro, AMD Ryzen 7 7840HS

andywenxh · 发表于 2025-02-05 12:14:25

Hi

I have a Beelink SER7 Mini PC W11 Pro, AMD Ryzen 7 7840HS
But it cannot startup, please let me know how to reset it back to factory setting?

tuiguang10 · 发表于 2025-02-05 16:05:22

Hello Andy,

Could you please send us a picture of  SN code at the bottom of machine ？

You can try to clear CMOS firstly: First,please unplug the power supply and HDMI cable.
Please press the pinhole of "CLR CMOS" with a pin for about 10 seconds.Ten minutes later, plug the power supply and HDMI cable, turn on the PC again.  Please wait about one or two minute, if you can go to the system.
Please repeatedly press delete key as soon as your restart the PC, go to BIOS. Go to Boot option, enable fast boot, press F4 to save.
Here is the tutorial https://mega.nz/file/2nIRGaYI#M2 ... pfyHlqyjnn86TypZp2w

1、Here is the tutorial of resetting the system:
1）Enter the safe mode, and reset the system.
      Start your PC, just as Windows attempts to load (spinning dots), press and hold Power Button for 5 - 10 seconds to perform a Hard Shut Down
      Do this many times until Windows  boots into the Recovery Environmen.

2）If Windows will boot into the Recovery Environment and from there you can access System Repair, Safe Mode, Command Prompt . . . etc.
      Please try each option one at a time, then see of Windows will boot . . .
      Go to Troubleshoot - Advanced Option - Startup Repair
      See if Windows startup can repair itself
      Go to Troubleshoot - Advanced Option - System Restore
      Check to see if you have a restore point you can go back to
      If you do not have a Restore Point, go to Troubleshoot - Advanced Option - Startup Settings and click Restart
      Upon restart, press 4 to enter Safe Mode
      Once in Safe Mode, backup your data if you do not already have a backup
      Open Device Manager and check to make sure all your Drivers are up to date
      Reboot to see if Windows will start Normally

3）If the above fails, go to Troubleshoot - Advanced Options - Reset this PC
      Choose to keep your files and apps, just your files or to keep nothing
      Then start the Reset

Hope it can help you!
Have a nice day!

andywenxh · 发表于 2025-02-10 04:30:30

Good morning, my SER7 cannot startup, it stuck at the Beelink logo. No windows boot up.
I'll send the picture of the machine bottom soon

andywenxh · 发表于 2025-02-10 04:46:52

Here is the bottom of my SER7 machine:

tuiguang10 · 发表于 2025-02-10 16:36:42

andywenxh replied at 2025-02-10 04:46
Here is the bottom of my SER7 machine:

Hello there,

Here are the possible solutions:

①Please press delete key as soon as you restart the PC, so that you can go to BIOS. Then go to boot page, set SSD as the first option. Please also send us a picture of the page of Safe&Exit.

②Please take out the SSD and reset it securely.

③Please reinstall the system.

It is recommended that you can go to Microsoft official website to download the corresponding win11 system file to install, this is the tutorial: https://url.bee-link.cn/74zu

Please remember to backup the data.

Have a nice day!

andywenxh · 发表于 2025-02-11 10:46:45

Thanks, I'll try this solution 3

tuiguang10 · 发表于 2025-02-11 16:39:46

andywenxh replied at 2025-02-11 10:46
Thanks, I'll try this solution 3

Hello Andy,

You are welcome. We are happy to help you.
If you have any updates , please feel free to contact us.

Have a nice day!