GT1 is dead

Zyxious

Same problem as Uncensored.
I've also flashed my GT1 with GT1_312M0_20170504 but from USB.
Now the GT1 has lights but no signal goes to the tv.

I have the same board as brooklyn2001. Can anyone tell us which pins to short?
Also should we do it when the unit is powered or without power? And for how long?

miticofuro

http://www.androidiani.com/forum ... 39.html#post7856489

Krendelyok

The short-circuiting of the contacts shown in the photo causes a short-circuit on the output of the voltage regulator, which forms the voltage for the memory chip. As a result, memory is started after the processor starts. The result of this barbarism can sometimes be a successful memory recovery. But this method, firstly, can lead to hardware problems, and secondly, the result largely depends on luck.

miticofuro

Krendelyok replied at 2017-06-09 15:41
The short-circuiting of the contacts shown in the photo causes a short-circuit on the output of the  ...

Then what is it right to do?
thank you

Zyxious

Chomee, helped me to Identify the points to short circuit and I managed to unbrick my GT1!
I'll try to  give you the details.

I flashed my GT1 S912 with a faulty rom, GT1_312M0_20170504 and it got bricked. Unabled to flash with it USB burning Tool since it didn't connect to my computer. This is what I've done to unbrick it.

1. Install USB Burning Tool v2.0.5.15 from Beelinks forum <http://www.bee-link.com/Beelink-2379-1-1.html>. I installed this on my Windows 10 laptop. Dot forget the drivers that are installed via an extra dialog during installation
2. Start the burning tool, I used english.
3. Open up the GT1 and connect it to the computer via USB to USB cable. No need to hold reset, just plug it in.
4. Now short circuit the points in the image below a second or so. You will hear a squeeky sound. You vill hear Windows play the usual USB connection sound if it was done correctly. Try to short circuit it a couple of times if it doesn't work the first time.
5. Load for instance GT1_113M0.img, after GT1 has connected. It can be found here <http://www.bee-link.com/Beelink-3410-1-1.html>
6. Press start to burn.
7. The GT1 should be unbricked after compleation.
8. Just plugg it in as to the tv usual. I had to restart mine once to get to the installation screens.
Thanks again to Chomee form showing me the pins.
Hope this helps someone.

miticofuro

Zyxious replied at 2017-06-10 20:29
Chomee, helped me to Identify the points to short circuit and I managed to unbrick my GT1!
I'll try  ...

5. Load for instance GT1_113M0.img, after GT1 has connected. It can be found here <http://www.bee-link.com/Beelink-3410-1-1.html>

link NOT WORK

UNCENSORED

Now short circuit the points in the image below a second or so. You will hear a squeeky sound. You vill hear Windows play the usual USB connection sound if it was done correctly. Try to short circuit it a couple of times if it doesn't work the first time.

How to this step?

miticofuro

UNCENSORED replied at 2017-06-10 22:42
Now short circuit the points in the image below a second or so. You will hear a squeeky sound. You v ...

Zyxious

miticofuro replied at 2017-06-10 22:05
5. Load for instance GT1_113M0.img, after GT1 has connected. It can be found here

link NOT WORK ...

The link works form me.
Try this then
New firmware to improve the problem of google play stopped work(standrad edition
<http://www.bee-link.com/forum.ph ... 0&fromuid=14737>
or search for "New firmware to improve the problem of google play stopped work(standrad edition"

Zyxious

UNCENSORED replied at 2017-06-10 22:42
Now short circuit the points in the image below a second or so. You will hear a squeeky sound. You v ...

Are you sure you want to do this if you don't know what short circuit is?

Take some metal e.g. a paper clip, bend it open and put one end on the top pin and the other end on the end pin, just do this for a second or so.

I take no responsibilities...