[GT1 Ultimate] Help for wallpaper, notification bar and navigation bar?

webipsum · Post time 2020-09-02 10:52:20

Edited by webipsum at 2020-09-02 23:17

Hello.
Regarding the previous question, I had difficulty in formulating it and will have difficulty in elaborating on it.

I have another question:
The mouse arrow on the GT1's screen appears but is very small and sometimes I can't see it. How do I increase the size of the mouse arrow?
EDIT:
I found out why:
I'm using it on a 4k (2160p60hz) TV.
If I switch to 1080P60hz, the mouse arrow will be appropriately sized.
How can this be resolved?
Thank you.

webipsum · Post time 2020-09-04 02:22:32

Good afternoon.
I updated the firmware following the instructions from 707N0 to 709N0.
Success! I was using it without any problems.
However I noticed that in the settings I didn't have the option to put the GT1 to sleep after a certain time.
As I like this facility, I decided to return the previous firmware (707N0).
I did exactly the same steps, with the same cable, the same USB Burning Tool, the same computer.
GT1 is connecting easily, but always stop in 7% formating.
I made an attempt with the GT1_707N0_AP6255.img firmware and the GT1_709N0_AP6255_20180719.img firmware, to no avail!
Please. I ask for your help.
I'm sending a screen with the error code.
Thank you.

webipsum · Post time 2020-09-04 05:15:25

News
After about 30 attempts, where I did the step by step I knew, which I read and did the other time, and I was not successful in Second Brush: SD Upgrade Mode and with Burn Card Maker and did the following:

I opened the USB Burning Tool (as an administrator) (as before),
Open the image (in the case GT1_707N0_AP6255.img) (as before),
I pressed START (as before),
I connected the USB cable to the computer (USB 2.0 port) (as before),
I connected the power plug to the Beelink GT1 Ultimate, (I previously ONLY PERFORMED THIS STEP after the GT1 was connected to the USB Burning Tool),
I connected the USB cable to the GT1's USB port, (as before),
GT1 connected at the first attempt and correctly applied the firmware until the end.

That's how it happened!
Learning remains!

webipsum · Post time 2020-09-04 10:14:22

beelink replied at 2020-09-01 09:52
I'm sorry I don't understand the suspend option you are talking about. Can you elaborate on it? An ...

Hi.
The option that exists on 707N0 and I didn't find it on 709N0 is this!
Tks.

beelink · Post time 2020-09-04 15:56:08

webipsum replied at 2020-09-04 10:14
Hi.
The option that exists on 707N0 and I didn't find it on 709N0 is this!
Tks.

Hello, first of all, it is about burning the firmware. It is recommended that you do not burn the firmware multiple times under normal circumstances. This may damage the machine

Second, have you successfully burned the firmware now? Still stuck at 7%? If it is stuck at 7%, it is a troublesome thing, usually you need to try to replace the usb cable, computer, and connection port to try to deal with this matter.

Third, can you change the interface to English and show your last picture to me again? By the way, tell me the process of how you click to that step, such as Setting>

In addition, I suggest you use your favorite firmware, because each firmware has different characteristics, and the newer firmware is not necessarily the better to use, and the best one is suitable.

webipsum · Post time 2020-09-04 20:10:50

Edited by webipsum at 2020-09-05 02:51

Hello, first of all, it is about burning the firmware. It is recommended that you do not burn the firmware multiple times under normal circumstances. This may damage the machine

"Second, have you successfully burned the firmware now? "YES! Tks! Ok!

Second, have you successfully burned the firmware now? Still stuck at 7%? If it is stuck at 7%, it is a troublesome thing, usually you need to try to replace the usb cable, computer, and connection port to try to deal with this matter.

I made it!

Third, can you change the interface to English and show your last picture to me again? By the way, tell me the process of how you click to that step, such as Setting>

Attached screenshot. Setting >>> Screen saver >>> Put device to sleep

In addition, I suggest you use your favorite firmware, because each firmware has different characteristics, and the newer firmware is not necessarily the better to use, and the best one is suitable.

I fully agree!

The mouse arrow on the GT1's screen appears but is very small and sometimes I can't see it. How do I increase the size of the mouse arrow?

Is it possible to increase the size of the mouse arrow? 1080P ok! 4K Very Small!

Tks!

beelink · Post time 2020-09-07 10:02:41

webipsum replied at 2020-09-04 20:10
"Second, have you successfully burned the firmware now? "YES! Tks! Ok!

I made it!

Regarding the problem of pointer size and screen sleep, I have two corresponding operations here (but I am not sure if your current firmware version is feasible)
Pointer size:
Settings>(driod settings>more settings>accessibility>large mouse pointer)
Hibernation: I don’t have the option to close the hibernation here, only adjust the duration. The position I adjust here is
Settings>(driod settings>more settings>display>no sleep)

webipsum · Post time 2020-09-07 22:32:35

Edited by webipsum at 2020-09-07 22:43

beelink replied at 2020-09-07 10:02
Regarding the problem of pointer size and screen sleep, I have two corresponding operations here ( ...

Perfect!
I'm using firmware version 707N0 (GT1_707N0_AP6255_20171106):

Pointer size: Settings>(driod settings>more settings>accessibility>large mouse pointer)

Perfect. I found the option and configured it here. Wonderful!!!

Hibernation: I don’t have the option to close the hibernation here, only adjust the duration. The position I adjust here is Settings>(driod settings>more settings>display>no sleep)

In version 707N0, I am solving this way: Setting >>> Screen saver >>> Put device to sleep
What firmware version are you using?
Could you send me a screenshot?
Is it possible to adjust the time to go into hibernation / sleep?
Can you tell if the latest firmware version 709N0 (GT1_709N0_AP6255_20180719) has this hibernation / sleep setting?

After a while, the image with the Beelink logo is blurred at startup (see image). But this is a detail that does not concern me.

For now, I will keep the 707N0 version of the firmware. This firmware version is serving me.
Your attention is being spectacular!
Tks!

beelink · Post time 2020-09-08 09:27:25

webipsum replied at 2020-09-07 22:32
Perfect!
I'm using firmware version 707N0 (GT1_707N0_AP6255_20171106):
Perfect. I found the option a ...

Sorry, because my SN code is different from yours, our firmware is also different, then you may not have this option
I am adjusting the brightness of the screen. There will be this option, which is the display. Please find if there is a similar