Mini S does not start after reboot

intin

The fan is humming and that's all.

The same situation if I turn on the computer immediately after shutting down.

Sometimes it happens when the computer goes to sleep after a set time. The cooler works, the computer does not come out of sleep.

I have to turn off the computer with the button and disconnect the power supply for a while. After these procedures - booting is normal.

Bios reset to default. Win11 21H2

orhor

I have similar behavior. I found out that overheating is the reason.


I tried to do everything in BIOS but unsuccessfully. It seems to me, that the OS cannot controll the fan. I tried Fan Control, i tried Speed Fan, none of them can see the fan nor control it.

intin

I don't have overheating.
min=47℃
max<80℃

intin

Looks like you're right.
In normal use, I have a temperature of 53-63℃. It's very rarely 80℃. I didn't realize such temperatures could be critical to iron.
But it's definitely not a software problem.
I was restoring the system disk from an early backup when the reboot worked. The problem hasn't gone away. Rebooting from WinPE doesn't work either, if you load the processor briefly before rebooting.

aleksfes

Hi!
I have the same issue. CPU max 20-25%, temp max 65℃, Ubuntu Server.
If I do reboot or shutdown and turn the device on, cooler is starting, hdd is creaking, but nothing happens. Ubuntu does not start, empty screen, even no BIOS logs. I should wait for 5 minutes, only after such a pause the device starts normally without any issue.

tuiguang16

Hello there,

Thanks for your letter and sorry for the late reply.

Please email us with belowing information:

1. Please tell us your problems again.
2.Please send us the photo of SN on the bottom of your pc and the purchase record.

Here is the email address---Support-PC@bee-link.com

It is more convenience for us to help you solve this issue through email.

Looking forward to your information.
Have a nice day!
Yuki

intin

Hi!
I put an additional external fan on the intake. Here are my temperatures under normal use:

But under serious load, the computer hangs on reboot. This usually happens during an upgrade. I turn off the power and wait for a while. What do I have to look forward to? That one day it just wouldn't turn on.
Why don't you say anything? You don't know what the problem is? Or don't know a way to fix it.
I have a soldering iron. I have a soldering station. Will this help me solve the problem?
For my tasks s mini is completely satisfactory to me.

intin

deleted

tuiguang16

Hello there,

Thanks for your letter and sorry for the late reply.

Here are some potential solutions that you can have a try.

1. You can reinstall the system, please back up your data first, restalling the system will lose your data.

Here is the Win11 system for MINS ----https://mega.nz/file/bvxQQKTD#K1 ... LL2t-viUiRuwmfrWpb0
Here is the Tutorial----https://beelink.oss-cn-hongkong. ... ystem%20Tutoria.pdf

Different models of machines have different systems, the above systems is for MINS.

2. Please unplug the power supply and HDMI cable. Please try to hit the hole of "CLR CMOS" with a needle or a pin for about 10 seconds.Ten minutes later, plug the power supply and HDMI cable, turn on the PC again.

3. There might be something wrong with the hard ware components.Please take out the SSD and RAM and then put them back , make sure they are installed properly.

Also please clean the gold finger with a rubber.Here is the tutorial  https://www.youtube.com/watch?v=hEd_7nmWVOk  
If it still doesn’t work, please try to replace SSD and RAM or put the SSD or RAM to other devices to test if they work.

4. You can take out one of the RAM and test whether one of the RAM is damaged.

Looking forward to your feedback so that we can help you better.

zann

is this solved? because i have the same problem
i have cmos cleared, unplug ram, ssd and plug it back
still no luck

i cant try the ram on other pc , because this is my only pc