Need Firmware Update for GT1 Ultimate 3GB/32GB G912GSHH90333

chamu666 · 发表于 2019-10-16 06:16:56

Hi All,

As per the Subject I am looking for a Stable Rom for my GT1 Ultimate.

Any help will be really appreciaated.

Thank you in Advance

chamu666

beelink · 发表于 2019-10-16 18:30:55

Please try to install the firmware in the link
http://www.bee-link.com/forum.ph ... amp;extra=#pid54856

chamu666 · 发表于 2019-10-16 21:46:07

Hi Admin,

My device gives error UBOOT/Disk initialize/Send command/Error result.

Also I tried Alvatech firmware. Same issue

Please assist

chamu666 · 发表于 2019-10-17 03:53:21

I am getting this error now:

[01:21:19 013][HUB5-1][Inf]--Device is connected
[01:21:19 013][HUB5-1][Inf]--Close device handle 0x0000082c
[01:21:19 064][HUB5-1][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#6&1dab0cb1&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x0000082c
[01:21:24 115][HUB5-1][Inf]--2-2-0-0
[01:21:24 115][HUB5-1][Err]--CheckFileRunState failed
[01:21:25 088][HUB5-1][Err]--[0x10303004]Romcode/Switch status/Identify/Error result
[01:21:25 088][HUB5-1][Inf]--Close device handle 0x0000082c

chamu666 · 发表于 2019-10-17 03:59:44

chamu666 replied at 2019-10-16 21:46
Hi Admin,

My device gives error UBOOT/Disk initialize/Send command/Error result.

New Error:

[01:27:36 849][HUB2-2][Inf]--Device is connected
[01:27:36 849][HUB2-2][Inf]--Close device handle 0x00000854
[01:27:36 909][HUB2-2][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#6&39bc3b9e&0&2#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x00000854
[01:27:41 973][HUB2-2][Inf]--0-7-0-16
[01:27:41 973][HUB2-2][Inf]--CheckFileRunState succeed
[01:27:41 973][HUB2-2][Inf]-- low_power
[01:27:41 973][HUB2-2][Inf]--Send command success
[01:27:41 973][HUB2-2][Inf]--Read command status success
[01:27:41 973][HUB2-2][Inf]-------------Download meson1.dtb-----------
[01:27:41 973][HUB2-2][Inf]--0-7-0-16
[01:27:41 973][HUB2-2][Inf]--Enc(0xadfc318c)
[01:27:41 973][HUB2-2][Inf]-- download mem dtb normal 141312
[01:27:41 973][HUB2-2][Inf]--Send download command success
[01:27:41 989][HUB2-2][Inf]--Read command status success
[01:27:42 013][HUB2-2][Inf]--Transfer complete
[01:27:42 013][HUB2-2][Inf]--Send download get_status command succeed
[01:27:42 017][HUB2-2][Inf]--get_status success
[01:27:42 524][HUB2-2][Inf]-------------ERASE FLASH-----------
[01:27:42 524][HUB2-2][Inf]--disk_initial 1
[01:27:42 524][HUB2-2][Inf]--Send command success
[01:28:42 536][HUB2-2][Err]--usb_reap_async_nocancel Try 2 time! usbReadFile len=512, ret=-116 error_msg=libusb0-dll:err [_usb_reap_async] reaping request failed, win error: The I/O operation has been aborted because of either a thread exit or an application request.

[01:28:42 536][HUB2-2][Err]--Check command return failed
[01:28:42 585][HUB2-2][Err]--[0x32030201]Uboot/Get result/DiskInitial error
[01:28:42 585][HUB2-2][Inf]--Close device handle 0x00000854