no work GT1 ULTIMATE ! help!

daniel0178 · Post time 2019-01-20 07:07:49

Edited by daniel0178 at 2019-01-20 07:22

hello friend, I have a GT1 ultimate, code S / N B706DB and it was perfect until yesterday, it came out system error message and I had to remove power cable to try to turn on again but never more turned on!

only the BEELINK logo appears on the screen and it does not pass from there!

in the recovery mode everything I try gives error, I can not do factory reset or anything!

I tried to install new firmware via USB but only the android appears in gray and the word UPGRADE ...

and it never happens from there!

help please!

Phant0m`` · Post time 2019-01-20 07:14:13

Hi daniel0178.

Please provide me with the URL to the firmware package that you have tested. Thank you. :)

daniel0178 · Post time 2019-01-20 07:26:27

Edited by daniel0178 at 2019-01-20 07:34

link of page ANDROIDPC.ES and this metod http://www.bee-link.com/forum.ph ... iewthread&tid=41741

:L

Phant0m`` · Post time 2019-01-20 07:37:51

daniel0178 replied at 2019-01-19 19:26
link of page ANDROIDPC.ES and this metod http://www.bee-link.com/forum.ph ... iewthread&tid=41741

: ...

Thanks.

Yes, this is the correct firmware package for the GT1 box containing the first five digits B706DB.

So try again USB flashing method. When using this flashing utility, keep default ' Configuration ' settings... Erase flash - Normal erase. Erase bootloader - Yes

and make sure that the Flashing utility reports 100% successfulness.

daniel0178 · Post time 2019-01-20 07:45:55

I've already tried and I get an error, even try to do it manually from APPLY APDATE FROM EXT, but still giving error

any other suggestions?

daniel0178 · Post time 2019-01-20 08:46:02

i need link to Firmware (GT1-705NO) con Chip WiFi QCA9377 desde SD

please!

links down all ...

daniel0178 · Post time 2019-01-20 09:32:23

all firmware aply , always this ....

Phant0m`` · Post time 2019-01-20 09:36:00

daniel0178 replied at 2019-01-19 19:45
I've already tried and I get an error, even try to do it manually from APPLY APDATE FROM EXT, but st ...

I don't think you understand... There are two packages for every Beelink firmware announcement, the SD Card package that you can use via Micro-SD Card or USB drive.

The USB firmware image for a full reload of the box via PC. http://www.bee-link.com/forum.ph ... &extra=page%3D1

daniel0178 · Post time 2019-01-20 10:09:56

if I understand, I have not yet tested with USB cable to the pc, but if I try all the roms 704 , 707 , 708 , 709 by Sd Card and all have given the same result, the gray android image above !

so I understand the correct version for my model would be the GT1_709D0_20180702 , tomorrow I get the missing cable I will try through the pc -

Phant0m`` · Post time 2019-01-20 11:34:53

daniel0178 replied at 2019-01-19 22:09
if I understand, I have not yet tested with USB cable to the pc, but if I try all the roms 704 , 707 ...

Correct. For GT1 with the first five digits of the serial number being ' B706D ' you need firmware package from Beelink firmware announcement post;

' GT1_up do date_709D0 S/N: A706D And B706D ' http://www.bee-link.com/forum.ph ... hread&tid=41741

You don't need the USB cable, you can use the Micro-SD card approach. However you use the USB Flash image ( *.IMG ) for Full flashing of the box.

How to unbrick / revive any Amlogic devices.
http://www.bee-link.com/forum.ph ... amp;extra=#pid59400

:)