|
Edited by danny94 at 2018-02-09 04:31
Hi,
on my beelink GT1 Ultimate i tried to install supersu, after that i was stucking in a bootloop.
This way i followed that guide:
http://www.bee-link.com/Beelink-28438-1-1.html
--> did SD-Card flash.
AND was flashing the correct firmware. My S/N begins with AX12 (q201) -> AP6255
But now after plug in im getting instantly a green screen and nothing happens.
Help please ? :'(:'(
I tried to use the usb_burning_tool but this stucks on 7%.
EDIT(07/02):
I uploaded the errors i found on the sd card after flashing the files from the link above via sd methode.
EDIT2(08/02):
Btw after the sd card flash i cannot do another one because of the green screen.
EDIT3(08/02):
Short description of my try hardings to flash with usb burning tools.
Was using:
-2 different usb cables, one short one long.
-3 different pcs (2x win7, 1x win10)
- mostly using 2.0 usb and the ports (i tried all) on the back side
- tried a lot different images
- nothing was connected to the box (even not the hdmi cable)
- on the box used the usb port close to the sd card slot
- tried combinations with plugged dc adapter and pressing the reset button while beginning to flash
- tried different versions (flash tool) 2.0.8, 2.0.9, 2.1.2
Already working on it more then 10 hours.
Please help, im very depressed ;(.
USB Burning tool error:
- <div>[21:15:18 663][HUB5-8][Inf]--Device is connected</div><div>
- </div><div>[21:15:18 663][HUB5-8][Inf]--Close device handle 0x000005c8</div><div>
- </div><div>[21:15:18 713][HUB5-8][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#5&565ea77&0&8#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x000005c8</div><div>
- </div><div>[21:15:23 764][HUB5-8][Inf]--0-7-0-16</div><div>
- </div><div>[21:15:23 764][HUB5-8][Inf]--CheckFileRunState succeed</div><div>
- </div><div>[21:15:23 765][HUB5-8][Inf]-- low_power</div><div>
- </div><div>[21:15:23 769][HUB5-8][Inf]--Send command success</div><div>
- </div><div>[21:15:23 772][HUB5-8][Inf]--Read command status success</div><div>
- </div><div>[21:15:23 772][HUB5-8][Inf]-------------Download meson1.dtb-----------</div><div>
- </div><div>[21:15:23 773][HUB5-8][Inf]--0-7-0-16</div><div>
- </div><div>[21:15:23 773][HUB5-8][Inf]--Enc(0xadfc318c)</div><div>
- </div><div>[21:15:23 773][HUB5-8][Inf]-- download mem dtb normal 137216</div><div>
- </div><div>[21:15:23 774][HUB5-8][Inf]--Send download command success</div><div>
- </div><div>[21:15:23 787][HUB5-8][Inf]--Read command status success</div><div>
- </div><div>[21:15:23 802][HUB5-8][Inf]--Transfer complete</div><div>
- </div><div>[21:15:23 803][HUB5-8][Inf]--Send download get_status command succeed</div><div>
- </div><div>[21:15:23 806][HUB5-8][Inf]--get_status success</div><div>
- </div><div>[21:15:24 306][HUB5-8][Inf]-------------ERASE FLASH-----------</div><div>
- </div><div>[21:15:24 306][HUB5-8][Inf]--disk_initial 1</div><div>
- </div><div>[21:15:24 306][HUB5-8][Inf]--Send command success</div><div>
- </div><div>[21:15:24 360][HUB5-8][Err]--failed:[21:15:24 360][HUB5-8][Err]--Check command return failed</div><div>
- </div><div>[21:15:24 364][HUB5-8][Err]--[0x32030201]Uboot/Get result/DiskInitial error</div><div>
- </div><div>[21:15:24 364][HUB5-8][Inf]--Close device handle 0x000005c8</div>
Copy the Code
|
|