GT1_311M0 QCA9377 （ultimate）edition

beelink · Post time 2017-04-18 11:07:25

hello , here is the link for GT1_311M0 QCA9377 （ultimate）edition , you can use it free. :loveliness:

Magendanz · Post time 2017-04-28 06:49:56

The GT1 Ultimate I received today came with GT1_312M0, Would you please post the official Amlogic burn package and SD update for these on the forum?

Just diffing the /system directory contents vs. GT1_311M0, it looks like there have been updates to TvSettings.apk, VideoPlayer.apk, and Camera2.apk. Nothing else stands out.

miticofuro · Post time 2017-04-28 18:09:07

My serial is on the box and on the tv box starts with A912 then WiFi AP6225
But if I use drm info and cpuz looks like a WiFi CQA9377 (see photo)

Which of the two is right?

Magendanz · Post time 2017-04-29 03:37:33

The serial number is right. Yes, for some crazy reason Beelink appended "_9377" to the strings in the build.prop for product name, device and board even if the device doesn't use the Qualcomm QCA9377 chipset.

lakiii · Post time 2017-05-19 23:09:22

After update GT1_312M0 bricked my Beelink. Thank you Beelink :@

smason · Post time 2017-05-19 23:13:33

Edited by smason at 2017-05-19 23:15

lakiii replied at 2017-05-19 23:09
After update GT1_312M0 bricked my Beelink. Thank you Beelink

Re-flash the full firmware GT1_312M0.

Requirement:
- USB male-male cable
- GT1_312M0_20170504.img firmware file
- setup_v2.0.5.15_build8.exe USB_Burning_Tool software
- paperclip (to push reset button at the bottom of the hole)

NOT required: power supply because during the flash phase the power is taken from USB port of your PC

Road map:
Install USB_Burning_Tool for AMLogic chip. Lunch it and open the second chinese TAB of the GUI, change to English.
Open File TAB and choose Import image, than load the GT1_312M0_20170504.img file from the hard drive of your PC.

Now take in your hand the case of your GT1 or GT1 Ultimate without any cable attached on it. Find the little hole in the bottom of the chassis and train your hand to push the reset button. If you hear the clic of the reset button and finally your hand it can handle the new exercise, you are ready to do the action useful to flashing the GT1*.

Action: push reset button at the same time insert the USB male cable to the port nearest to the micro SD slot. Now Windows OS recognize a new device and the USB_Burning_Tool find the device and list it.

Now you are ready to push "Start" in the GUI of USB_Burning_Tool... wait the and of procedure... Successful line message.

GAME OVER!

miticofuro · Post time 2017-05-20 01:45:56

lakiii replied at 2017-05-19 23:09
After update GT1_312M0 bricked my Beelink. Thank you Beelink

Ota update ?

lakiii · Post time 2017-05-20 03:24:05

Update with SD Card

lakiii · Post time 2017-05-20 06:40:34

smason replied at 2017-05-19 23:13
Re-flash the full firmware GT1_312M0.

Requirement:

Thank you my friend but this method did not help. My PC is still not seen Beelink.
I had to open beelink and short the 2 pins.
My Beelink again alive :D:D:D

daodzen · Post time 2017-05-20 23:26:21

lakiii replied at 2017-05-20 06:40
Thank you my friend but this method did not help. My PC is still not seen Beelink.
I had to open b ...

Hi!

How did you do that??
I flash GT1_311M0 and device bricked.
Tried to restore by pressing micrо-button inside - proccess does not start, flash burning tool do not recognize device. For now, but yesterday it was reconized and flashed with no probles. Same comp, same cable, same port.

Pls help to unbrick, anyone?(