View: 5445|Reply: 8

GT1 ultimate bricked S912 ddr4

[Copy link]

1

Threads

1

Posts

17

Credits

Newbie

Rank: 1

Credits
17
Post time 2017-09-06 05:42:07 | Show all posts |Read mode
Same problem has most here... White light on, doesn't work. Had latest android TV, USB burning tool successfully flash but noting happens; official firmware or custom nothing solves. I'm a computer specialist, what else can i do? my device is almost 3 months!

Reply

Use magic Report

17

Threads

725

Posts

6171

Credits

Moderator

Rank: 7Rank: 7Rank: 7

Credits
6171
Post time 2017-09-06 05:45:51 | Show all posts
You going to have to revive your box by downloading the EPROM for the firmware version that you was running before attempting to upgrade. What is the first four digits of your serial number...? can be found by looking at the bottom of your Beelink box.

You'll need to download Amlogic Burn Card Maker v2.0.2 utility and make bootable SD Card using this EPROM file. It doesn't matter if you can't get into recovery mode, or if there's no signal to TV.

Insert the Micro-SD card in, and unplug the power adapter from the box. Insert the paper-clip end into the RESET hole and carefully press down and hold the button in. Carefully hook up the power adapter while maintaining the RESET button down for the duration of five - seven seconds. After which time you can release the RESET button, and leave the box sit for however long it takes for it to reprogram and re-boot itself. You'll finally see signal from Beelink to TV and be entering the Beelink setup phase. :o
Beelink GT1 Mini (95X2) w/CoreELEC & Android 9 (Pie)
Reply Support Not support

Use magic Report

17

Threads

725

Posts

6171

Credits

Moderator

Rank: 7Rank: 7Rank: 7

Credits
6171
Post time 2017-09-06 05:48:00 | Show all posts
Wait a minute... Did you have enabled ' Erase flash ', and select ' Erase all ' under ' Configurations ' settings? That should have worked with USB Burning Tool to fix that.
Beelink GT1 Mini (95X2) w/CoreELEC & Android 9 (Pie)
Reply Support Not support

Use magic Report

391

Threads

4189

Posts

110K

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
12735
Post time 2017-09-07 11:48:44 | Show all posts
dear , tell me all information about your GT1  and then i can know where the errors lies . :loveliness:
Reply Support Not support

Use magic Report

391

Threads

4189

Posts

110K

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
12735
Post time 2017-09-07 11:49:08 | Show all posts
Phant0m`` replied at 2017-09-06 05:48
Wait a minute... Did you have enabled ' Erase flash ', and select ' Erase all ' under ' Configuratio ...

:loveliness:
Reply Support Not support

Use magic Report

2

Threads

16

Posts

59

Credits

Member

Rank: 2

Credits
59
Post time 2017-09-07 13:11:01 | Show all posts
i have done the same as per Phantom instructions but nothing happend.................

Please help me. my gt1 ultimate is not working after the update and now reset button is not working how I ll flash it with sd card.

I made sdcard as per instructions and pressing the hole but nothing happend
Reply Support Not support

Use magic Report

2

Threads

16

Posts

59

Credits

Member

Rank: 2

Credits
59
Post time 2017-09-07 13:14:56 | Show all posts
Please guide me how to detect the sd card to flash my box,,,,,,,,,,,,,,,,,,,,,,,,,,

as there is only White Light............ no ON/OFF

no blink ........ nothing
Reply Support Not support

Use magic Report

1

Threads

3

Posts

31

Credits

Newbie

Rank: 1

Credits
31
Post time 2018-05-16 03:11:30 | Show all posts
Phant0m`` replied at 2017-09-06 05:45
You going to have to revive your box by downloading the EPROM for the firmware version that you was  ...

Hello Phantom,
      
I have same problem, I have a GT1 Ultimate bricked, only white light is on
and does not recognized from pc when connecting with usb m/m.
I tried to flash with sd card method but didn't recognized at all.
Can you help me please?

Best regards.
Reply Support Not support

Use magic Report

0

Threads

1

Posts

18

Credits

Newbie

Rank: 1

Credits
18
Post time 2018-06-23 17:24:07 | Show all posts
Anything new? i Have The same issue, can not enter recovery anymore...only while light is on.

Reply Support Not support

Use magic Report

You have to log in before you can reply Login | Sign up

Points Rules

Quick Reply To Top Return to the list