Brick after supersu

ECGT80

Guys i have big problem after install supersu and restart, nothing works burning tool only 4%, burn card maker all img firm, sd card method minus. nothing work hdmi no detect how solved this......?

Phant0m``

kumara29 replied at 2017-08-27 08:52
what cable did you plug ? power cable to  GT1 ?

Yes... Person was talking about the Power cord

beelink

hello dear , tell me more information about your GT1 and I will choose the right firmware for you to have a try again , thank you .:hug:

ECGT80

Hello, at first I had the GT1-703NO version installed for the AP6255 (GT1 Ultimate), it seems that from the play store I installed Supersu, I install the binaries, and then it asks me to restart and I make a normal restart from supersu from here. Problems was left in the image of loading and did not finish turning on then between the recovery and I did not work the remote control of vol up neither the bottom nor the arrows, nothing simply turned off with any button that pressed and then restarted then I wanted to use the burning tool and it only reaches me 4% (I never run this tool I do not know why) then I wanted to use the "Burn Card Maker" use a 2GB Sdcard memory in FAT and turned on and started with the "Upgrade" Was about 5 minutes not even appeared the installation bar and turned off the HDMI connection after that wait a long time and nothing (30 minutes) so I decided to turn it off and on again and now Not even HDMI connection does not recognize it use several img with "burn card maker" and everything was in vain I can not relive the pc if it recognizes but only reaches 4% as always. any solution????

Sorry for my english

Español:
Hola, en un principio tenia instalado la version GT1-703NO para el modelo AP6255  (GT1 Ultimate) resulta que desde play store instale Supersu, instalo los binarios concluyo y luego me pide reiniciar y realizo un reinicio normal desde supersu a partir de ahy surgieron mis problemas se quedaba en la imagen de cargando y no terminaba de encender entonces entre al recovery y no me funcionaba el control remoto de vol arriba ni el de abajo ni las flechas, nada simplemente se apagaba con cualquier boton que presionaba y se volvia a reiniciar entonces quise utilizar el burning tool y solo me llega al 4% (Nunca me funciono esta herramienta no se porque) luego quise utilizar el "Burn Card Maker" utilice una memoria de 2GB Sdcard en FAT y encendio y empezo con el mensaje de "Upgrade" estuvo asi unos 5 minutos ni siquiera aparecio la barra de instalacion y se apago se corto la conexion HDMI luego de eso espere bastante tiempo y nada (30 minutos) entonces decidi apagarlo y volverlo a encender y ya ni siquiera existe conexion HDMI no lo reconoce utilice varios img con "burn card Maker" y todo fue en vano no logro revivirlo la pc si lo reconoce pero solo llega al 4% como siempre. alguna solucion????

ECGT80

This solved, I needed energy so I put the plug of the cable to the device (and not just with the USB cable) to be able to install the software through USB Burning Tool, Thanks ...

kumara29

ECGT80 replied at 2017-08-03 07:23
This solved, I needed energy so I put the plug of the cable to the device (and not just with the USB ...

what cable did you plug ? power cable to  GT1 ?

kumara29

USB firmware upgrading don't need power cable as per tutorial video by beelink

kumara29

Phant0m`` replied at 2017-08-27 21:33
Yes... Person was talking about the Power cord

Thanks alot Phant0m & ECGT80

Plugging power cable to GT1 Ultimate. i was able to upgrade firmware.

ECGT80

Note: For me only work when no work hdmi output when turn on box.

Nota: para mi solo solo me funciono este metodo cuando no conecta el hdmi al encender el tv box

freez

Hi guys!I have the same problem,only burning to stop at 7%,the TV does not see the console via hdmi.I tried different solution to the problem mentioned on the forum,but neither of which did not help.beelink gt,1(A912).2g/32g.